Dialogic & Loop Start Guida di Installazione Scaricare il pdf

Installing the Dialogic®

Brooktrout® TR1034 Analog

PCI Express Board

Part Number: 931-159-06

The Dialogic® Brooktrout® TR1034 Analog PCI

Express boards (“TR1034” or “TR1034 Board(s)”) are

full-sized, single-slot, PCI Express serial I/O

bus-compatible fax boards. They provide the

following:

 On-board analog loop start connections

 V.34 (33.6 Kbps) fax transmission speeds

 Up to eight fax and voice channels per board

The TR1034 Analog PCI Express Series boards use

3.3V and 12.0V power from the serial bus and can be

inserted into the x4, x8, or x16 bus (signaling) slot.

You need a voice or fax application to use a

TR1034 Analog board. Dialogic does not provide the

application or a driver for this board. Normally, you

purchase the application and driver from a third party

vendor.

This installation guide provides information about:

 Safety Compliance Statements

 System Requirements (including telephone service)

 Setting the Module Number

 Installing the TR1034 Board

 Recognizing PCI Express Slots

 Connecting the Phone Service

 Understanding LED Signals

 Using the TR1034 Analog Board

 Getting Help

Safety Compliance Statements

 Install this board only in UL Listed equipment that

has instructions stating that the user may install and

remove accessory boards.

 Disconnect any TNV circuit connectors (telephone

line cords) from this board before removing the

cover of the equipment.

System Requirements

This board must be installed in an enclosure that meets

the following specifications:

 A Pentium or later host processor

 A PCI Express serial I/O bus slot that is at least

x4 wide. See

Recognizing PCI Express Slots for

more information.

 Temperature: 0 C - 50 C

 Humidity: 10% - 90% (non-condensing)

 Power Requirements:

The following is also required:

 Telephone service: analog loop start interface

Setting the Module Number

Set each board to a unique module number to easily

identify the resources associated with a specific board

in a multi-board system.

Use the SW-1 rotary switch (Figure 1) to set a unique

module number for each Brooktrout Fax Board. See

Figure 5 for the switch location. Select a number from

2 - F on the rotary switch. Settings 0 and 1 are reserved

and cannot be used.

Figure 1. Rotary Switch (SW-1)

Installing the TR1034 Board

To install your board:

1. Turn off your PC and remove the cover.

2. Locate a free PCI Express bus slot (see Figure 2).

3. Carefully align the board with the slot and firmly

seat the PCI Express Board Edge connector into

the PCI Express slot..

4. Tighten the mounting bracket screw to secure the

board to the chassis.

5. Replace the cover.

6. Turn on your computer.

Note: Brooktrout Fax Boards should not be present in the

computer during the installation of any operating system.

The operating system might misinterpret the board as

being some other device, with unpredictable

consequences.

Recognizing PCI Express Slots

The PCI Express slots in the computer chassis appear

as black slots. The TR1034 Analog board has a PCI

Express board edge connector. It can be inserted into

any one of the PCI Express slots shown in Figure 2.

Figure 2. PCI Express Serial Bus Slots

Connecting the Phone Service

The appropriate telephone service and hookups must

be installed at your site in order to connect to

telephone service. The following table shows the

channel/connector relationship:

Use the cable supplied with the board. Use the

following instructions to connect your board to Analog

Loop Start service:

1. Plug one end of the cable into the RJ-45 telephone

connector on the board.

Connect to Connector A for channels 0-3 or to

Connector B for channels 4-7 (see Figure 4 to

locate connectors).

2. Plug the other end into the wall connector for your

telephone service.

See Figure 3 for pinout details for your board:

Figure 3. Analog Connector Pinouts

Board +3.3V +3.3 Aux +12V Total Power

2 chan

1.4A 0.050A 0.025A 5.1W

4 chan

1.45A 0.050A 0.050A 5.5W

8 chan

1.5A 0.050A 0.10A 6.3W

Caution: A small amount of static electricity can

destroy the sensitive components on your board.

To prevent static damage, always connect yourself

to ground using a ground strap before touching a

circuit board. Handle boards only by the edges or

metal mounting brackets and transport boards in

an anti-static bag.

Warning: When installing the board, be sure that

the mounting bracket is securely fastened to the

chassis and the chassis is plugged into a

grounded three prong plug. Improper chassis or

bracket grounding can result in harmful or fatal

electrical shock as well as component damage.

PCI Express Board

Edge Connector

PCI Express x4 slot

PCI Express x8 slot

PCI Express x16 slot

Insert board connector into any of

these slots

Channel

Number

RJ-45

Connector Type of Service

Analog Loop Start

Tip 2

Ring 2

Tip 1

Ring 0

Tip 0

Ring 1

Tip 3

Ring 3

Port A

Tip 6

Ring 6

Tip 5

Ring 4

Tip 4

Ring 5

Tip 7

Ring 7

Port B

1 2

Sommario

Pagina 1

Installing the Dialogic® Brooktrout® TR1034 Analog PCI Express BoardPart Number: 931-159-06The Dialogic® Brooktrout® TR1034 Analog PCI Express boards

Pagina 2 - Getting Help

Più documenti per Networking Dialogic & Loop Start

Per vedere il documento Dialogic & Loop Start Guida di Installazione

Dialogic & Loop Start Guida di Installazione (2 pagine)

Commenti su questo manuale

Nessun commento

Dialogic & Loop Start Guida di Installazione

Navigare online o scaricare Guida di Installazione per Networking Dialogic & Loop Start. Dialogic & Loop Start Installation guide [en] Manuale Utente

Sommario

Più documenti per Networking Dialogic & Loop Start

Commenti su questo manuale

Prodotti e manuali riguardandi Networking Dialogic & Loop Start