Dialogic D/41D Manuale Utente

Navigare online o scaricare Manuale Utente per Hardware Dialogic D/41D. Dialogic D/41D User Manual Manuale Utente

  • Scaricare
  • Aggiungi ai miei manuali
  • Stampa
  • Pagina
    / 2
  • Indice
  • SEGNALIBRI
  • Valutato. / 5. Basato su recensioni clienti
Vedere la pagina 0
D/41D & D/21D
n Configuration
n Installation
n Warranty Period
n RMA Process
n Regulatory Notices
05
-
0294
-
003
Copyright © 1997
Dialogic Corporation.
All Rights Reserved.
Read Me First
Protect Yourself from Electric Shock
To reduce the risk of electric shock:
n Switch off the power and remove power cords
before opening the computer case to install the
D/41D or D/21D.
n Do not re-attach power cords and switch on power
to the computer while the computer case is removed.
Protect the Board from Static Electricity
Computer boards are static-sensitive and can be damaged
by touching or handling them. To prevent damage from
static electricity, do the following:
n Wear a grounded, static-dissipative wrist-strap for
the entire hardware installation.
n Keep the board in its anti-static container when it is
not being handled.
n Work at a static-safe work area (see Figure 1).
Ground
Common
Ground
Point
G
r
o
u
n
d
d
S
t
t
i
-
D
i
i
p
t
i
v
Wrist Strap
Grounded
Static-Dissippative
Mat
Figure 1. Static-safe work area
A static-safe work area consists of a grounded static-
dissipative wrist strap and a work surface covered with
or composed of a grounded static-dissipative material.
The work surface drains electrical charges from conduc-
tive materials when the materials are placed on the sur-
face. The grounded static-dissipative wrist strap drains
static charge from the person wearing the strap. Both
components ensure that static charges are drained at a
rate and current level that are safe. Both must be used
any time a person is handling any component.
Read Your Software Documentation
Your application software or Dialogic software release
(hereinafter collectively called “voice software”) may
have special installation or configuration instructions or
requirements. Be sure to read all software documentation
for any such instructions or requirements.
Installation Order
You can install the D/41D or D/21D and voice software
in any order, but Dialogic recommends that you install
the voice software first when running in a Windows
95
or Windows NT
environment, and board first in any
other operating system environment.
D/41D or D/21D Factory Defaults
You may be able to use the factory defaults when install-
ing the D/41D or D/21D board. Read through these
instructions and check for possible interrupt level (IRQ)
and memory address conflicts between the D/41D or
D/21D board and other software or hardware devices
(for example, video card or CD ROM controller card)
before installing the board.
Note: If you own a software utility that can determine
what IRQs and memory addresses are in use, run it to
help determine potential conflicts before installing the
D/41D or D/21D. Some voice software includes such a
software utility, or a separate board configuration utility,
to help with the D/41D or D/21D installation and
configuration.
Configuring the
Hardware
Configuring Multiple Voice Boards (JP7)
You can install up to 16 D/41D or D/21D boards in a
system. One and only one board in a system can have
the jumper on JP7 installed (see D/41D Physical
Description):
n One board: Leave the jumper on JP7 installed
(default).
n Multiple boards: Remove the jumper on JP7 from
all but one board.
1
2
3
4
S
W
1
:
1
S
W
1
:
2
S
W
1
:
3
S
W
1
:
4
J
P
6
J
P
5
IRQ 3
IRQ 4
IRQ 5
IRQ 6
IRQ 7
IRQ 2/9
Figure 2. Top edge view of SW1, and JP6/5 and Side
view of Jumper Block JP1
Setting the Hardware Interrupt Level (JP1)
The default hardware interrupt level (IRQ) is IRQ 2/9;
IRQ 2 is used when the board is installed in an XT-type
PC and IRQ 9 is used with an AT-type PC.
Change the IRQ by moving the jumper on jumper block
JP1 (see Figure 2) to another IRQ setting if IRQ 2 or 9 is
in use by another device.
Note: Set every D/41D and D/21D board in the system
to the same IRQ level.
Set the Memory Address
Each D/41D or D/21D and compatible voice board
installed in a computer must have a unique memory
address consisting of a base memory address segment
and an offset address.
Set the Base Memory Address Segment
(JP5 and JP6)
The default base memory address segment for the D/41D
and D/21D is D000H (Hexadecimal). Generally, you
should use the default unless there are more than eight
boards in your system or if other non-Dialogic devices in
your system must use the D000H segment. Select the
base address memory segment with jumpers JP5 and JP6
(see Figure 2) as follows:
Base Address
(Hex)
JP6 / JP5
Top Edge View
JP6
JP5
D000
(default)
removed removed
A000
removed installed
B000
installed installed
C000
installed removed
* Be aware of possible conflicts with devices that often
use
these segments: video adapters; disk controller
BIOS.
Set the Offset Address (SW1:1, 2, 3)
The default offset address for the D/41D and D/21D is
0000H. Each D/41D and D/21D board in your system
requires a unique address, so you must change the offset
address on every additional D/41D and D/21D board. If
you need to change an offset address, set the switches 1,
2, and 3 on SW1 (see Figure 2) as follows:
Offset
Address
SW1:1, 2, 3
Top Edge
SW1: Switches
(Hex) View 1 2 3
0000
(default)
1 2 3 4
off off off
2000
1 2 3 4
off off on
4000
1 2 3 4
off on off
6000
1 2 3 4
off on on
8000
1 2 3 4
on off off
A000
1 2 3 4
on off on
C000
1 2 3 4
on on off
E000
1 2 3 4
on on on
n While you can map only one D/41D or D/21D
board to an offset, you can set multiple boards to
consecutive offsets within a base memory
segment as shown in the following example.
Board
Base:Offset (Hex) D/41D Lines
1
2
3
D000:0000
D000:2000
D000:4000
1–4
5–8
9–12
n Write the IRQ level and memory address settings
below for use when installing system software:
IRQ Base Offset Lines/Board
D41/D Physical Description
SW1
JP5
JP6
JP101
JP201
JP301
JP401
JP7
JP1
P3
JP8
J2
J1
* Note: The D/21D board does not have jumpers JP301 and JP401.
Part
J1–J2
JP1
JP5JP6
JP7
JP8
JP101
JP401*
P3
SW1
Function
RJ-14 Connectors for interface
with PBX or CO lines
Jumper block to set interrupt
level
Jumper to set base memory
segment
Jumper to enable hardware
interrupt circuitry
Jumper to select the built-in loop
start interface or an external
interface (DTI/124 T-1 card)
Jumpers to set ring detection
threshold
Connector for Analog Expansion
Bus (AEB)
Switch to set the offset address
and default line state
Vedere la pagina 0
1 2

Sommario

Pagina 1 - D/41D & D/21D

D/41D & D/21D n Configuration n Installation n Warranty Period n RMA Process n Regulatory Notices 05-0294-003 Copyright © 1997 Dialogic C

Pagina 2 - Regulatory Notices

Setting the Initial Hook Switch State (SW1:4) SW1 switch 4 (SW 1:4 in Figure 2) sets the initial hook switch state for the D/41D and D/21D board. This

Modelli collegati D/21D

Commenti su questo manuale

Nessun commento