Dialogic Brooktrout Digital Board Specifiche Scaricare il pdf

Installing the

Dialogic

Brooktrout

Digital

Board (Multiple Spans)

Part Number: 931-111-06

The Dialogic® Brooktrout® digital boards (formerly

known as Dialogic® Brooktrout® TR1000 Series

digital boards and also referred to herein as “board”)

are telephony platforms for T1/E1 switch-based and

packet network services. The Dialogic® Brooktrout®

digital board provides a range of boards combining

telephony and media that includes

Dialogic® Brooktrout® TR1034 products that

provide a platform for fax applications

You need a separate fax application to use the digital

board. Please contact your application provider for the

correct operating system driver, supporting files, and

firmware.

Operating/Environmental Specifications

This device must be installed in an enclosure that

meets the following electrical and mechanical

requirements:

 Power requirements: 5A at 5 VDC = 25W

maximum per PCI slot

 Temperature: 0°C - 50°C

 Operating humidity: 10% - 95% (noncondensing)

 Storage requirements: -40 to 100 degrees C

ambient

 Supply voltages: interfaces to 5V from the PCI

host backplane. Onboard DC-DC converters will

generate all required onboard voltages at 5%

regulation.

 MTBF (mean time between failures):

>32,000 hours

Loca

ting the Serial Number and MAC Addres

You can find the board serial number (2 letters and 9

digits) and MAC address (00A08A and 6 more digits)

on white labels on the back of the board.

Setting the Module Number (SW1)

You must set each board to a unique module number

to identify the resources associated with a specific

board in a multi-board system (to a maximum of 4

boards). SW1 (Figure 1) is a rotary switch (see

location in Figure 2). Use it to set the module number

for each board. The available settings are 2 - F (0 and

1 are reserved).

Figure 1. Rotary Switch - SW1

Using the H.100 Termination Switch

On a single board or on multiple boards installed in

the same chassis, leave the H.100 Termination Switch

in the OFF position. Multiple boards in the same

system do not require a connecting H.100 cable.

Figure 2. Dialogic® Brooktrout® Digital Board

The H.100 Termination Switch (see Figure 2 for

location) controls termination for the H.100 clock

signals. If you have the board and other boards that

need to be connected using an H.100 cable (not

supplied), you must terminate the H.100 clock signal.

Only the boards at each end of the cable must be

terminated. All other boards must not be terminated

(see Figure 3).

Figure 3. Setting Clock Termination in a Series of

Boards Connected by an H.100 Bus

Set the switch to ON (slide towards the end of the

board that contains the T1/E1 and Ethernet interface

connectors) to terminate the H.100 clock on the

board. The LED lights when the switch is set to the

ON position. Slide the switch towards the back of the

board to turn the switch to the OFF position.

Note: The H.100 Termination Switch LED is located on

the opposite side of the board, behind the

termination switch.

Installing the Dialogic® Brooktrout® Digital

Board

Read the product instructions for installing hardware

and software before installing your board so that you

install them in the proper order.

To install the board:

1. Power off the computer.

2. Remove the computer cover. If the system has a

board hold-down bar, remove that as well.

3. Locate an unused PCI expansion slot and remove

the blank bracket.

4. Holding the board at each top corner, insert the

board firmly into the PCI slot.

5. Screw the board’s mounting bracket securely to

the computer's frame. See Figure 2.

6. Attach the connector on the H.100 cable to the

connector on the board, if needed.

7. Replace the computer cover.

8. Turn on the computer.

The board status LED (see Figure 5) continuously

flashes yellow when you turn the computer on.

Note: Dialogic® Brooktrout® Digital boards should not

be present in the computer during the installation

of any operating system. The operating system

can misinterpret the board as being some other

device, with unpredictable consequences.

H.100 Clock Termination Switch

H.100 Bus Connector

Mounting Bracket

Rotary Switch (SW1)

PCI Connector

T1/E1

Connector

Ethernet

Connectors

Set the H.100 switch

to the ON position.

Set the H.100 switch

to the ON position.

Set H.100 switches

on these boards to

the OFF position.

A small amount of static electricity can

destroy the sensitive components on

your board. To prevent static damage,

always connect yourself to ground

using a ground strap before touching a

circuit board. Handle boards only by

the edges or metal mounting brackets

and transport boards in an anti-static

bag.

When installing the board, be sure that

the mounting bracket is securely

fastened to the chassis and the chassis

is plugged into a grounded three prong

plug. Improper chassis or bracket

grounding can result in harmful or fatal

electrical shock as well as component

damage.

1 2

Sommario

Pagina 1 - Board (Multiple Spans)

Installing the Dialogic® Brooktrout® Digital Board (Multiple Spans)Part Number: 931-111-06The Dialogic® Brooktrout® digital boards (formerly known as

Pagina 2 - Getting Help

Recognizing PCI SlotsThe board is compliant with the following: 32/64 bit, 33 MHz/66 MHz, PCI-SIG 2.3 chassis PCI-X chassis up to 66 MHzThe PCI conn

Più documenti per Networking Dialogic Brooktrout Digital Board

Per vedere il documento Dialogic Brooktrout Digital Board Specifiche

Dialogic Brooktrout Digital Board Specifiche (2 pagine)

Commenti su questo manuale

Nessun commento

Dialogic Brooktrout Digital Board Specifiche

Navigare online o scaricare Specifiche per Networking Dialogic Brooktrout Digital Board. Dialogic Brooktrout Digital Board Specifications Manuale Utente

Sommario

Più documenti per Networking Dialogic Brooktrout Digital Board

Commenti su questo manuale

Prodotti e manuali riguardandi Networking Dialogic Brooktrout Digital Board